International network for natural sciences – research journal
  • mendeley icon
  • linkedin icon
  • google plus icon
  • twitter icon
  • google scholar icon
  • facebook icon

Comparison of some mechanical and physical properties of heat cured soft denture liner after the addition of polyamide nylon-6 micro particle

By: Mohanad Saleem, Abdalbseet A Fatalla

Key Words: Polyamide, peel bond, acrylic soft liner.

Int. J. Biosci. 13(3), 338-347, September 2018.

DOI: http://dx.doi.org/10.12692/ijb/13.3.338-347

Certification: ijb 2018 0001 [Generate Certificate]

Abstract

The longevity of soft denture liners depend on it is properties, that is why, defects in the material properties may reduce the service life of soft lining materials and necessitate its replacement. The aim of this study was to evaluate the effect of adding different concentrations of Polyamide-6 (Nylon-6) on the peel bond strength, tensile strength and wet ability of acrylic base heat cure soft liner. 120 samples were fabricated by the addition of 0%, 1%, 2% and 3% by weight PA-6 micro-particles powder to acrylic soft liner. The study samples were divided into three(3) groups according to test to be performed, each group containing 40 samples, 10 specimens for each concentration of PA-6 micro particle (0%,1%,2% and3%). The data were analyzed with a descriptive statistical analysis, one-way ANOVA, and Bonferroni multiple comparison test. The mean values of peel bond  and tensile strength of 1% PA-6 reinforcement group increased significantly when compared to control group and higher than the mean values of other experimental group. On other hand, there was non-significant elevation in wettability property after addition of different percentage of PA-6 micro particle powder(1%,2% and 3%). The 1% PA-6 reinforcement improved peel bond as well as tensile strength with higher value among other percentages (2% and 3%) , also improved the wettability property of acrylic soft liner.

| Views 38 |

Comparison of some mechanical and physical properties of heat cured soft denture liner after the addition of polyamide nylon-6 micro particle

Alcibiades JZ, Gregory LP, Robert G, Jagger MGJ. 2001. Wettability of Visible Light–Curing Denture Lining Materials, International Journal of Prosthodontic 14(3), 250-254.

Al−Nema LM. 2011. The Influence of Saliva, Artificial Saliva and Propolis Extract on the Wettability of Heat−Cured and Visible Light−Cured Denture Base Material,  Al–Rafidain Dental Journal, 11(1).

Al-Shaikhli MS, Khamas AH. 2012. Comparative study of wettability of different lining, tissue conditioning and denture base materials (in-vitro study), Journal of Baghdad College Dentistry, 24, (special issue 1).

American Society for Testing and Materials ASTM. D903-93 . Standard test method for peel or stripping strength of adhesive bonds. ASTM, Philadelphia.

Demir H, Dogan A, Dogan M, Keskin S, Bolayir G, Soygun K. 2011. Peel Bond Strength of Two Silicone Soft Liners to  a Heat-cured Denture Base Resin. Journal of  Adhesive Dentistry 13(6), 579-584.

Fatihallah AA, Alsamaraay MA. 2017. Effect of Polyamide (Nylon 6) Micro-Particles Incorporation into RTV Maxillofacial Silicone Elastomer on Tear and Tensile Strength, Journal of Baghdad College Dentistry 29(4).

ISO 37. 2011. Rubber, vulcanized or thermoplastic—Determination of tensile stress-strain properties.

Kawano F, Dootz ER, Koran A, Craig RG. 1992. Comparison of bond strength of six soft denture liners to denture base resin. Jpurnal of Prosthodontic Dentistry 68, 368-371.

Kutay O. 1994. Comparison of tensile and peel bond strengths of resilient liners . Faculty of Dentistry, The Journal of Prosthetic Dentistry 71(5), 525-531.

Monsenego PH, Baszkin A, De-Lourdes CM, Lejo-Yeux T. 1989. Complete denture retention. Part II: Wettability studies on various acrylic resin denture base materials. Journal of  Prosthetic Dentistry 62, 308-312.

Muttagi S, Subramanya JK. 2017. Effect of incorporation seed oils on the antifungal property, surface roughness , wettability, weight change, and glucose sorption of a soft liner.  Journal of Prosthetic Dentistry 117(1), 178-185.

Mutluay MM, Ruyter IE. 2005. Evaluation of adhesion of chairside hard relining materials to denture base polymers, Journal Prosthetic Dentistry, 94, 445-452.

Mutluay MM, Ruyter IE. 2007. Evaluation of bond strength of soft relining materials to denture base polymers. Journal of Dental Materials 23, 1373-1381.

Oguz S, Mutluay MM, Dogan OM, Bek B. 2007. Effect of thermo cycling on tensile strength and tear resistance of four soft denture liners. Dental Materials Journal 26, 296-302.

Pisani MX, Silva-Lovato CH, Malheiros-Segundo L, Macedo AP, Paranhos HF. 2009. Bond strength and degree of infiltration between acrylic resin denture liner after immersion in effervescent denture cleanser, Journal of Prosthodontic 18, 123-129.

Sanchez-Aliaga  A, Pellissari CV, Arrais CA, Michel MD, Neppelenproek KH,  Urban VM. 2016. Peel bond strength of soft lining materials with antifungal to a denture base acrylic resin, Dental Materials Journal, 35(2), 194–203.

Sertgöz A, Kulak Y, Gedik H, Taskonak B. 2002. The effect of thermocycling on peel strength of six soft lining materials. Journal of Oral Rehabilitation 29, 583-587.

Waters MG, Jagger RG. 1999. Mechanical properties of an experimental denture soft lining material. Journal of Dentistry, 27, 197-202.

Wood WE, Johnson DL, Duncanson MG. 1993. Variables affecting silicone polymethyl lnethacrylate interracial bond strength. Journal of Prosthodontic, 2, 13-18.

Wright PS. 1980. A physico-chemical study of soft lining materials for acrylic dentures. PhD Thesis, University of London.

Yassir AD. 2017. The effect of addition of zirconium Nano particle on antifungal  activity and some properties of soft denture lining material, M.Sc. Thesis college of dentistry, University of Baghdad.

Mohanad Saleem, Abdalbseet A Fatalla.
Comparison of some mechanical and physical properties of heat cured soft denture liner after the addition of polyamide nylon-6 micro particle.
Int. J. Biosci. 13(3), 338-347, September 2018.
https://innspub.net/ijb/comparison-mechanical-physical-properties-heat-cured-soft-denture-liner-addition-polyamide-nylon-6-micro-particle/
Copyright © 2018
By Authors and International Network for
Natural Sciences (INNSPUB)
https://innspub.net
brand
innspub logo
english language editing
  • CALL FOR PAPERS
    CALL FOR PAPERS
    Publish Your Article
  • CALL FOR PAPERS
    CALL FOR PAPERS
    Submit Your Article
INNSPUB on FB
Email Update